42STH IE
- Manual Quote
| Item | Specifications） |
|---|---|
| Step Angle | 1.8。 |
| Step Angle Accuracy | ±5% ( )(full step ,no load) |
| Shaft Radial Play | 0.02mm@450 g-load |
| Shaft Axial Play | 0.08mm@450 g-load |
| Max. radial force | 28N @ 20 mm from the flange |
| Max. axial force | 10N |
| Dielectric Strength | 600VAC /1s |
| Insulation Resistance | 100MΩ ,500VDC |
| Ambient Temperature | -20。C~+50。C |
| Insulation Class | Class B |
| FL42STH33-1334A-IE2· Phase current | 1.33 |
| FL42STH33-1334A-IE2· Resistance | 2.1 |
| FL42STH33-1334A-IE2· Inductance | 2.5 |
| FL42STH33-1334A-IE2·Holding torque | 0.22 |
| FL42STH33-1334A-IE2·Detent torque | 0.012 |
| FL42STH33-1334A-IE2· | 4 |
| FL42STH33-1334A-IE2·Rotor inertia | 35 |
| FL42STH33-1334A-IE2·Weight | 0.22 |
| FL42STH33-1334A-IE2· Length | 33.5±1 |
| FL42STH38-1684A-IE4· Phase current | 1.68 |
| FL42STH38-1684A-IE4· Resistance | 1.65 |
| FL42STH38-1684A-IE4· Inductance | 3.2 |
| FL42STH38-1684A-IE4·Holding torque | 0.36 |
| FL42STH38-1684A-IE4·Detent torque | 0.015 |
| FL42STH38-1684A-IE4· | 4 |
| FL42STH38-1684A-IE4·Rotor inertia | 54 |
| FL42STH38-1684A-IE4·Weight | 0.28 |
| FL42STH38-1684A-IE4· Length | 39.5±1 |
| FL42STH47-1684A-IE4· Phase current | 1.68 |
| FL42STH47-1684A-IE4· Resistance | 1.65 |
| FL42STH47-1684A-IE4· Inductance | 2.8 |
| FL42STH47-1684A-IE4·Holding torque | 0.44 |
| FL42STH47-1684A-IE4·Detent torque | 0.02 |
| FL42STH47-1684A-IE4· | 4 |
| FL42STH47-1684A-IE4·Rotor inertia | 68 |
| FL42STH47-1684A-IE4·Weight | 0.35 |
| FL42STH47-1684A-IE4· Length | 47.5±1 |
| Specifications | (Unit) |
| InputVoltage / Input voltage (DC) | 12 | 24 | 32 | Vdc |
| OutputCurrent（Peak）/ Output current (peak) | 0.5 | - | 2.2 | A |
| Pulse / Step pulse frequency | 0 | - | 200 | KHz |
| PulseVoltage/ Pulse voltage | - | 5 | 5 | Vdc |
| ControlSignalInputCurrent/ Control signal input current | 7 | 10 | 16 | mA |
| Resistance/ Insulation resistance | 100 | - | - | MΩ |
| CurrentPeak | 0.5A | 0.7A | 1.0A | 1.2A | 1.5A | 1.8A | 2.0A | 2.2A |
| CurrentRMS | 0.35A | 0.5A | 0.7A | 0.85A | 1.0A | 1.28A | 1.42A | 1.58A |
| SW3 | ON | ON | ON | ON | OFF | OFF | OFF | OFF |
| SW2 | ON | ON | OFF | OFF | ON | ON | OFF | OFF |
| SW1 | ON | OFF | ON | OFF | ON | OFF | ON | OFF |
| Pin description | （Function） |
| +Vdc | 。 Power supply:12~32 Vdc, Including voltage fluctuation and EMF voltage. |
| GND | (Power Ground) |
| OPTO+（+5V） | Enable signal: this input is used to enable or disable the driver. When ENA+ is connected to +5 V and ENA- to low level (or the internal optocoupler conducts), the driver cuts off the motor phase currents and the motor becomes free; step pulses are not responded to. If this function is not needed, leave the enable terminal floating. |
| TXD | RS232 transmit |
| RXD | RS232 receive |
Description
Product Center Built-in Driver
Microstep Resolution Selection
2481620253264PU/Rev4008001600320040005000640012800SW6ONONONONOFFOFFOFFOFFSW5ONONOFFOFFONONOFFOFFSW4ONOFFONOFFONOFFONOFF
This motor can be customized to meet customer requirements.
